
Security Considerations in SD-WAN Deployment
By moving traffic onto the public internet and putting a smart, internet-facing device at every branch, SD-WAN gives enterprises the lower cost, faster site rollouts and direct paths to cloud applications they wanted from the WAN. But now, those devices are exactly what attackers are going after.
Verizon’s Data Breach Investigations Report (DBIR) found edge devices and VPNs accounted for 22% of exploitation-driven breaches, up from 3% a year earlier. In the latest edition, vulnerability exploitation became the single most common way attackers get in, at 31% of breaches.
How SD-WAN changes your security
Traditional MPLS networks backhauled branch traffic to a central data center, where a single security stack inspected everything. Performance suffered but control was simple.
SD-WAN breaks traffic out locally. A branch reaches Microsoft 365 or Salesforce directly over the internet, which is faster and cheaper. It also means every branch now has its own front door and every SD-WAN appliance is an internet-facing edge device that needs the same care as a data center firewall.
The risks that come with it
- More points of exposure. Each local internet breakout is a place where threats can enter without passing through central inspection.
- The appliance as a target. SD-WAN edge devices run software with vulnerabilities like any other. Exposed management interfaces are a favorite entry point. CISA’s Binding Operational Directive 25-02 now requires U.S. federal agencies to secure internet-facing management interfaces on edge devices because of widespread exploitation.
- Configuration drift. Hundreds of sites, multiple administrators and years of changes produce inconsistencies that can be hard to see.
- Split policy between networking and security. When SD-WAN and security come from different vendors with different consoles, rules vary and vulnerabilities form.
- Fast lateral movement. Once inside, attackers can move from a compromised branch device toward critical systems in under 30 minutes and in the fastest cases within seconds.
Six security considerations for SD-WAN deployment
1. Treat every SD-WAN edge as critical attack surface
According to the latest DBIR, organizations fully remediated only 26% of the critical vulnerabilities on CISA’s Known Exploited Vulnerabilities (KEV) catalog within a year. Because SD-WAN edge devices are primary entry points, treating them as low-priority risks leaves a critical vulnerability open far too long.
What to put in place:
- A defined patching SLA for SD-WAN software, with KEV-listed vulnerabilities fixed first
- Management interfaces that are never reachable from the public internet
- Multi-factor authentication and role-based access for every administrator
- Continuous mapping of known CVEs to the specific devices and software versions you run
2. Integrate security at every breakout
When branch offices route traffic straight to the internet, security must live at the point of egress. Enforcing consistent inspection at the local edge or via cloud-delivered security stops threats before they reach the network.
Capabilities to prioritize:
- Next-generation firewall with application awareness at the edge
- Intrusion prevention (IPS) to block exploit attempts in transit
- DNS security and URL filtering to stop connections to malicious and newly registered domains
- Anti-malware inspection for files crossing the breakout
3. Encrypt and authenticate the overlay
SD-WAN builds encrypted tunnels, typically IPsec, between sites and to cloud gateways. Encryption keeps data unreadable if intercepted, which supports HIPAA, PCI DSS and GDPR obligations. The details of how it is implemented decide how strong it really is.
What to confirm:
- Certificate-based device identity, so a rogue box cannot join the fabric
- Automated key rotation
- Secure zero-touch provisioning, so new devices authenticate before receiving configuration
- Your vendor’s roadmap for post-quantum cryptography, since encrypted traffic captured today could be decrypted in the future
4. Centralize policy and validate it continuously
A single management plane that pushes consistent policy to every site removes much of the risk of drift. Centralization alone isn’t enough, though. Policies need to be checked against what the organization intended and against established security frameworks, on an ongoing basis.
Practices that help:
- Template-based configuration for every site type
- Change control with an audit trail for every policy edit
- Continuous configuration analysis that flags deviations and compliance gaps as they appear, rather than at the next annual review
5. Converge SD-WAN and security into SASE
Secure Access Service Edge (SASE) combines SD-WAN with cloud-delivered security, known as security service edge (SSE), so the same policy follows users and traffic wherever they go. The market has steadily moved toward single-vendor SASE, where networking and security share one platform and one policy model, because split architectures are harder to run and easier to misconfigure.
Core SSE capabilities:
- Firewall as a Service (FWaaS) to inspect traffic at the cloud edge
- Secure Web Gateway (SWG) to filter web traffic and block malicious content
- Cloud Access Security Broker (CASB) for visibility and data control across SaaS applications
- Data Loss Prevention (DLP) to stop sensitive information from leaving through unauthorized channels
- Zero Trust Network Access (ZTNA) to verify every user and device and grant access only to specific applications
ZTNA deserves particular attention. Legacy VPNs give an authenticated user broad access to the network and run on exactly the kind of internet-facing appliance attackers target. ZTNA removes both problems.
6. Segment, monitor and respond around the clock
Assume something will get through and limit how far it can travel.
What to build in:
- Segmentation that separates guest, corporate, operational technology and payment traffic into isolated virtual networks
- Continuous monitoring of network flows and logs to establish behavioral baselines and spot anomalies
- AI-assisted detection that correlates network and security telemetry so real threats rise above the noise
- Incident response playbooks that cover compromised edge devices specifically, including how to isolate a site without cutting off the business
- DDoS protection for the internet circuits SD-WAN now depends on
Best practices for securing SD-WAN deployments
- Test regularly. Include SD-WAN appliances and management systems in penetration testing scope.
- Train the people who run the network. Network operations staff need to recognize signs of a compromised edge device as well as a failed link.
- Map controls to your regulations. Document how SD-WAN encryption, segmentation and logging support HIPAA, PCI DSS, GDPR, NIS2, or DORA. Auditors will ask.
- Ask vendors about vulnerability disclosure. Under the EU Cyber Resilience Act, manufacturers of products sold in the EU must now report actively exploited vulnerabilities within 24 hours. Find out how your SD-WAN vendor will tell you.
Managed or do-it-yourself?
Many of the risks above come down to operational discipline at scale: patching hundreds of devices on time, keeping policy consistent and watching the network 24 hours a day. That is hard to sustain with a stretched internal team.
A managed SD-WAN service shifts that work to a provider whose job is to keep the edge patched, consistent and monitored. For organizations with a large or global footprint, it is often the most reliable way to close the gap between deployment and protection.
How GTT secures SD-WAN
GTT combines SD-WAN with integrated security services, all running on its global Tier 1 IP backbone.
- Managed SD-WAN delivers secure, optimized connectivity for global enterprises, with GTT managing design, deployment and ongoing operations.
- Secure Connect is GTT’s SASE solution, converging SD-WAN with cloud-delivered security, including ZTNA, FWaaS, SWG and CASB.
- GTT Defense Halo continuously analyzes firewall and network device configurations against security frameworks, maps known CVEs to your monitored assets and detects behavioral anomalies at network speed. Halo Recon handles the configuration and exposure assessment that keeps SD-WAN policy honest across every site.
- DDoS Mitigation protects the internet underlay your SD-WAN depends on.
- Managed Detection and Response provides 24/7 threat monitoring and response.
For a practical plan to retire legacy VPN access, read From Plan to Protection: 7 Steps to Deploying ZTNA.
For a broader view of the branch and edge, see The IT and Security Leader’s Guide to Securing the Distributed Edge.
Planning an SD-WAN rollout or reviewing one already in place? Talk to our experts about building security in from the start.
Related resources
-
Learn more: Faster Than the Attack: How the Right Network-Based Solution Can Turn AI into the Optimal Cyber Defense

Faster Than the Attack: How the Right Network-Based Solution Can Turn AI into the Optimal Cyber Defense
Subscribe to the GTT Insider
Get the latest news, articles and resources about our
products and services.

